The Under Armour Curry 9 is Stephen Curry’s signature shoe for the 2021-22 NBA season. It’s a great basketball shoe but you can improve it. One of the easiest ways is by swapping the original insoles with Move insoles. They’re the perfect upgrade.

The Curry 9 fits Move Game Day and Game Day Pro insoles true to size. For example, if your shoes are a Men’s Size 11.5, use the 11-11.5 insole. 

The Curry 9 includes a light adhesive from the ball of the foot to the heel that attaches the stock insole to the shoe’s base. The adhesive is not strong so you can use your hands to easily pull the insole free of the shoe. Loosening the laces of the shoe will help make the switch easier. Once you’ve removed the stock insoles, you can slide the Move insoles into the shoes and adjust their position as needed. That’s the process. You'll be ready to play in your Move insoles in 2 minutes. 

For a more detailed explanation on removing and replacing the insoles on the Curry 9, please refer to the instructions below.

Under Armour Curry 9: How to Remove and Replace the Insole

Step 1: Loosen Laces and Remove Current Insole 

First, loosen the laces on the shoes as much as possible. This will make it easier to get the shoe’s tongue out of the way, remove the included insole and insert your new Move insole. The stock insole of the Curry 9 is attached to the shoe’s strobel board, the thin foam layer between the insole and the cushioning, with light adhesive. 

To remove the insole, slightly lift up on the middle edge of the insole near the arch area. Push your fingers further underneath the insole. Slowly lift up on the insole until the adhesive begins to detach. Next, slide your fingers towards the rear of the shoe and fully detach the insole from the heel. Then slide your fingers forward as far as possible to detach the adhesive from the toe area. You may not be able to reach the end of the insole due to space constraints inside the shoe. That’s ok. Once there’s only a small amount of adhesive left attached at the toe, gently pull the insole free. Remove the insole from the shoe and put it to the side. Repeat the process for the other shoe.

Tip: If for some reason the adhesive will not detach with light pulling, you can use a hair dryer set to low heat to warm and loosen the adhesive.

Step 2: Insert your Move Insoles

Now, grab the Move insole that matches the shoe. The sculpted arch and sawtooth pattern of the left insole are on the right side. The sculpted arch and sawtooth pattern of the right insole are on the left side. 

Hold the bottom of the insole and make sure your fingers are supporting the more flexible toe area. Starting with the toe area, begin to insert the insole into the shoe and use your hand to guide it towards the inside front. Due to space constraints, you may not be able to guide the insole all the way to the toe of the shoe. Get the end of the insole as close to the toe as you can. 

Then, move your hand back along the underside of the insole to the TPU section and push. Stop once the insole touches the inside toe of the shoe. Once the insole is in place, align it with the base of the shoe and push down until it settles into place. Slight adjustments may be needed to ensure the insole sits flush with the base of the shoe. Once the insole is secure in the first shoe, repeat the process for the second shoe.

Step 3: Checking the Fit

To check the insole’s placement and fit, slide your feet into the shoes, tie them and walk around. If the insole feels slanted or shifted to one side, remove the shoe and readjust the insole’s position.

The fit will feel different. Your foot will sit higher in the Curry 9, have more contact with the upper materials and feel slightly tighter. That’s normal. 

You should also immediately feel the extra cushion, support and frictionless nature of the Move insole. You’ve just upgraded your insole in multiple ways and your shoes will now have a closer, one to one fit. 

Tip: If you prefer a looser fit for casual wear (not recommended for basketball) you’ll want to go up in shoe size. Take your Move insoles with you when you try on shoes to ensure you find the proper fit.

When both insoles are secure, tie your shoes, and head to the court. You’re ready for a new, more comfortable, more supportive experience in the Under Armour Curry 9.

After you’ve had a great experience on court, please leave us a review. If you experienced any issues you couldn’t fix using the guide above, contact customer support here.