The Nike Blazer has had a recent surge in popularity. Everywhere you look, someone is rocking Blazers. There’s no denying the Blazer can match almost all outfits. What started out as a basketball shoe for on-court performance has now become a staple in almost everyone’s casual footwear rotation. But it’s a staple with hardly any cushioning and support. The addition of a Move insole can make a huge difference in the comfort.
The Nike Blazer fits Move Game Day and Game Day Pro insoles true to size. For example, if your shoes are a Men’s Size 6, use the size 6 insole.
The Nike Blazer includes a strong adhesive attaching the stock insole to the shoe’s base. You can use your hands to pull the insole free of the shoe. You can also stack the insole on top if needed. Loosening the laces of the shoe will help make the switch easier. Once you’ve removed the stock insoles, you can slide the Move insoles into the shoes and adjust their position as needed. That’s the process. You'll be ready to play in your Move insoles in 2 minutes.
For a more detailed explanation of removing and replacing the insoles on the Nike Blazer, please refer to the instructions below.
Nike Blazer: How to Remove and Replace the Insole
Step 1: Loosen Laces and Remove Current Insole
First, loosen the laces on the shoes as much as possible. This will make it easier to get the tongue out of the way, remove the included insole and insert your new Move insole. The stock insole of the Nike Blazer is attached to the shoe’s strobel board, the layer between the insole and the cushioning, with sticky adhesive.
To remove the insole, slightly lift the middle edge of the insole near the arch area. Push your fingers further underneath the insole. Slowly lift one of the insoles until the adhesive begins to detach. Next, slide your fingers towards the rear of the shoe and fully detach the insole from the heel. Then slide your fingers forward as far as possible to separate the adhesive from the toe area. You may not be able to reach the end of the insole due to space constraints inside the shoe. That’s ok. Once only a small amount of adhesive is left attached at the toe, gently pull the insole free. Remove the insole from the shoe and put it to the side. Repeat the process for the other shoe. If all else fails, you can stack Move Insoles on top.
Tip: If the adhesive will not detach with light pulling, use a hair dryer set to low heat to warm and loosen the glue.
Step 2: Insert your Move Insoles
Now, grab the Move insole that matches the shoe. The left insole's sculpted arch and sawtooth pattern are on the right side. The right insole's sculpted arch and sawtooth pattern are on the left.
Hold the bottom of the insole and ensure your fingers support the more flexible toe area. Starting with the toe area, insert the insole into the shoe and use your hand to guide it towards the inside front. Due to space constraints, you may not be able to guide the insole to the toe of the shoe. Get the end of the insole as close to the toe as possible.
Then, move your hand back along the underside of the insole to the TPU section and push. Stop once the insole touches the inside toe of the shoe. Once the insole is in place, align it with the shoe's base and push down until it settles into place. Slight adjustments may be needed to ensure the insole sits flush with the shoe's base. Once the insole is secure in the first shoe, repeat the process for the second shoe.
Step 3: Checking the Fit
To check the insole’s placement and fit, slide your feet into the shoes, tie them and walk around. If the insole feels slanted or shifted to one side, remove the shoe and readjust the insole’s position.
The fit will feel different. Your foot will sit higher in the Nike Blazer, have more contact with the upper materials, and feel slightly tighter. That’s normal.
You should also immediately feel the extra cushion and frictionless nature of the Move insole. You’ve upgraded your insole in multiple ways, and your shoes will now have a closer, one-to-one fit.
Tip: If you prefer a looser fit for casual wear (not recommended for basketball), you’ll want to go up in shoe size. Take your Move insoles with you when you try on shoes to ensure the proper fit.
When both insoles are secure, tie your shoes, and head to the court. You’re ready for a new, more comfortable, supportive experience in the Nike Blazer.
After you’ve had a great experience with Move Insoles, please leave us a review here. Contact customer support here if you experienced any issues you couldn’t fix using the guide above.